Solution Description:
DC motor is a rotating motor that can transform DC electric power into mechanical vitality (DC motor) or mechanical energy into DC electrical energy (DC generator). It is a motor that can convert DC and mechanical strength into one another. When it operates as a motor, it is a immediate current motor, which converts electrical power into mechanical power when it operates as a generator, it is a immediate existing generator, which converts mechanical vitality into electrical vitality.
| Merchandise Title | Big and medium DC Motor Marine propulsion Motor |
| Motor Variety | DC Motor,ACMotor,Stepper Motor,Asynchronous Motor ,Synchronous Motor (CZPT equipment) |
| Composition framework | The construction of DC motor ought to consist of two parts: stator and rotor. The static component of DC motor is called stator. The principal operate of stator is to produce magnetic discipline, which is composed of base, primary magnetic pole, commutation pole, stop cap, bearing and brush device. Running element is referred to as rotor, whose primary perform is to produce electromagnetic torque and inductive electromotive force. It is the hub of strength conversion of DC motor. So it is also commonly known as armature, which consists of rotor, armature core, armature winding, commutator and enthusiast. |
| Product | Z Sort |
| Seat quantity | Z315-Z1000 |
| power | sixty~2800kW |
| Voltage | 220~1000V |
| Torque assortment | one.five ~180kNm |
| Protection stage | IP23, IP44 |
| Cooling method | IC06,IC17,IC37,IC81W |
| Functioning speed | Constant Pace /Low Velocity /Change Velocity /Substantial Speed Other |
| Major classification | DC Motor is a equipment that converts mechanical vitality into DC energy. It is largely employed as DC motor for DC motor, electrolysis, electroplating, smelting, charging and excitation power provide of alternator. Even though in spots the place DC power is needed, AC energy rectifier is also utilised to change AC into DC energy, but from some facets of functionality, AC rectifier power source can not completely substitute DC generator. |
| Software | DC motors are extensively utilized in tape recorders, video clip recorders, online video discs, electric shavers, hair dryers, digital watches, toys and so on. |
| Maintenance approach | Expert motor maintenance center motor upkeep method: cleansing stator and rotor – changing carbon brush or other components – vacuum F stress dipping paint – drying – Calibration equilibrium. 1. Use setting need to be always dry, motor surface need to be held clean, air consumption should not be hindered by dust, fibers and other obstacles. two. When the thermal protection of the motor carries on to operate, it ought to be ascertained whether the fault arrives from the motor or the overload or the setting worth of the protective unit is too reduced. Following removing the fault, it can be set into operation. three, guarantee that the motor is nicely lubricated throughout operation. The common motor runs for about 5000 hours, that is to say, lubricating grease should be added or replaced. When bearing overheating or lubricating deterioration is found in procedure, the hydraulic strain should adjust lubricating grease in time. When changing grease, the aged grease must be taken out, and the oil groove of bearing and bearing include need to be washed with gasoline. Then ZL-3 lithium grease must be filled with one/two (two poles) and two/three (4 poles, six poles and 8 poles) of the cavity between the inner and outer rings of the bearing. four. When the daily life of the bearing is more than, the vibration and noise of the motor will increase naturally. When the radial clearance of the bearing reaches the following benefit, the bearing should be changed. five, when removing the motor, it is Ok to eliminate the rotor from the shaft extension or the non extension stop. If it is not required to unload the admirer, it is more handy to just take out the rotor from the non-axle extension finish. When pulling out the rotor from the stator, the stator winding or insulation must be prevented from getting ruined. six. When changing the windings, the sort, size, turns and gauges of the unique windings should be recorded. When these info are missing, they should be attained from the producer and the first created windings ought to be transformed at will, which often deteriorates one or a number of performance of the motor or even helps make it impossible to use them. |
