Product Description:
DC motor is a rotating motor that can change DC electric powered strength into mechanical energy (DC motor) or mechanical strength into DC electric power (DC generator). It is a motor that can convert DC and mechanical vitality into one particular an additional. When it operates as a motor, it is a direct recent motor, which converts electrical energy into mechanical vitality when it runs as a generator, it is a immediate recent generator, which converts mechanical strength into electrical power.
| Solution Title | high torque lower rpm gear motor electric torque hub motor |
| Motor Sort | DC Motor,ACMotor,Stepper Motor,Asynchronous Motor ,Synchronous Motor (CZPT equipment) |
| Composition framework | The structure of DC motor ought to consist of two parts: stator and rotor. The static part of DC motor is referred to as stator. The principal perform of stator is to produce magnetic area, which is composed of base, primary magnetic pole, commutation pole, end cap, bearing and brush system. Operating portion is known as rotor, whose major operate is to produce electromagnetic torque and inductive electromotive power. It is the hub of vitality conversion of DC motor. So it is also frequently referred to as armature, which is composed of rotor, armature core, armature winding, commutator and enthusiast. |
| Design | Z Type |
| Seat quantity | Z315-Z1000 |
| electrical power | sixty~2800kW |
| Voltage | 220~1000V |
| Torque variety | one.five ~180kNm |
| Safety amount | IP23, IP44 |
| Cooling mode | IC06,IC17,IC37,IC81W |
| Operating speed | Constant Velocity /Minimal Velocity /Change Velocity /Higher Speed Other |
| Main classification | DC Motor is a equipment that converts mechanical energy into DC electrical power. It is primarily used as DC motor for DC motor, electrolysis, electroplating, smelting, charging and excitation power offer of alternator. Though in places where DC power is needed, AC electrical power rectifier is also utilised to convert AC into DC electricity, but from some facets of functionality, AC rectifier electrical power supply can not completely substitute DC generator. |
| Application | DC motors are broadly used in tape recorders, online video recorders, online video discs, electric powered shavers, hair dryers, electronic watches, toys and so on. |
| Upkeep method | Specialist motor maintenance heart motor routine maintenance method: cleaning stator and rotor – replacing carbon brush or other areas – vacuum F force dipping paint – drying – Calibration balance. 1. Use environment should be always dry, motor area ought to be kept thoroughly clean, air consumption need to not be hindered by dust, fibers and other hurdles. two. When the thermal protection of the motor carries on to operate, it need to be ascertained whether or not the fault will come from the motor or the overload or the setting value of the protective system is as well low. Right after getting rid of the fault, it can be place into procedure. three, make sure that the motor is nicely lubricated throughout operation. The general motor runs for about 5000 hrs, that is to say, lubricating grease ought to be added or replaced. When bearing overheating or lubricating deterioration is located in operation, the hydraulic strain must alter lubricating grease in time. When replacing grease, the old grease need to be eliminated, and the oil groove of bearing and bearing protect must be washed with gasoline. Then ZL-3 lithium grease ought to be loaded with one/two (two poles) and two/three (4 poles, six poles and eight poles) of the cavity amongst the internal and outer rings of the bearing. four. When the existence of the bearing is more than, the vibration and sounds of the motor will enhance certainly. When the radial clearance of the bearing reaches the subsequent price, the bearing need to be replaced. five, when removing the motor, it is Ok to get rid of the rotor from the shaft extension or the non extension stop. If it is not essential to unload the supporter, it is far more practical to just take out the rotor from the non-axle extension conclude. When pulling out the rotor from the stator, the stator winding or insulation need to be prevented from getting destroyed. 6. When replacing the windings, the form, size, turns and gauges of the first windings must be recorded. When these knowledge are dropped, they should be acquired from the maker and the unique developed windings should be changed at will, which typically deteriorates 1 or numerous performance of the motor or even helps make it impossible to use them. |
